|
GME GME L/R-0- 22 |
Measurement of Interior Sound level for Motor Vehicles |
|
GME GME L/R-0- 38 |
Vehicle Squeak and Rattle Evaluation |
|
GME GME L/R-0- 6 |
Noise Comfort at Vehicles with AC |
|
GME GME L/R-12F- 1 |
Check Control Electronics |
|
GME GME L/R-12F- 2 |
Ride Control |
|
GME GME L/R-12G- 1 |
Functional Test of Horns |
|
GME GME L/R-12J- 3 |
LCD Instrument Cluster |
|
GME GME L/R- 1B/E/F/G/H03-16 |
Static Closing Force-:2006 |
|
GME GME L/R-1B/H- 6 |
Critical Clearance between Hood, Rear Compartment |
|
GME GME L/R-1C- 2 |
Roof Water Drainage |
|
GME GME L/R-1F/G03- 15 |
Door Opening Force |
|
GME GME L/R-1F/G03- 17 |
Inspection of Drop Windows |
|
GME GME L/R-1F/G- 1 |
Measurement of Frame Stiffness of Front and Rear Doors-Replaced by GMI L-1F/G-1 |
|
GME GME L/R-1F/G- 4 |
Door Water Drainage |
|
GME GME L/R-1H- 5 |
Tailgate Water Drainage - Estate (Station Wagon) and Minivan |
|
GME GME L/R-1H- 6 |
Tailgate and Luggage Compartment Lid Water Drainage - Hatchback and Notchback |
|
GME GME L/R-1J/K- 1 |
Seat Back Rigidity (Torsion Test) |
|
GME GME L/R-1J/K- 3 |
Requirements for Protection Against Load |
|
GME GME L/R-1J03- 4 |
Seat Adjuster under Driving Conditions |
|
GME GME L/R-1J05- 6 |
Frame Front Seat Back, Test in Service |
|
GME GME L/R-1T02- 2 |
Noise Analysis to the Articulation Index Method |
|
GME GME L/R-1T02- 3 |
Evaluation of Heater Blower Noise Emission |
|
GME GME L-0- 1 |
Measurements on Vehicle Air Conditioning Systems in the OPEL Environment Tunnel |
|
GME GME L-0- 11 |
Basic Test |
|
GME GME L-0- 12 |
Friction Test |
|
GME GME L-0- 13 |
High Frequency Test |
|
GME GME L-0- 14 |
Test for Lag of Damping Force |
|
GME GME L-0- 15 |
Low Temperature Test |
|
GME GME L-0- 16 |
High Temperature Test |
|
GME GME L-0- 19 |
Determination of Mass and Trim Heights |
|
GME GME L-0- 2 |
Determination of the Center of a Vehicle |
|
GME GME L-0- 20 |
Temperature Test |
|
GME GME L-0- 23 |
Calibration Procedure for Tooth Belt Tension Gauge |
|
GME GME L-0- 24 |
Checklist for the Initial Inspection of Durability Test Vehicles |
|
GME GME L-0- 3 |
Rotary Shaft Seal Durability Test-Includes Appendix A-E |
|
GME GME L-0- 37 |
Test Procedure for Signal Generation and Execution of Simulated Durability Tests |
|
GME GME L-0- 39 |
Functional Noise Measurement in Stationary Vehicles-Replaced by GMW14055 |
|
GME GME L-0- 4 |
Single Step Test |
|
GME GME L-0- 5 |
Dynamic Strength Test |
|
GME GME L-0- 8 |
Stair-Case-Test to Dixon and Mood |
|
GME GME L-0- 9 |
Test for Bolt Loosening |
|
GME GME L-1- 1 |
Body Distortion |
|
GME GME L-1- 10 |
Sound Deadening of Body |
|
GME GME L-1- 19 |
Transverse Stiffness of Bonnet/Load Compartment Cover Hinge |
|
GME GME L-1- 2 |
Body in White: Determination of Resonant Frequency |
|
GME GME L-12H- 1 |
Ground Connections |
|
GME GME L-12L- 2 |
Anti-Theft Warning Device |
|
GME GME L-12L- 3 |
Low Frequency Interferences over Vehicle Electrical System |
|
GME GME L-1- 3 |
Rollover Test |
|
GME GME L-13A- 1 |
Radiator Durability Test |
|
GME GME L-13D- 1 |
Coolant Flow Through Heater Core in the Vehicle |
|
GME GME L-13D- 2 |
Determination of Heater Core Characteristics |
|
GME GME L-1A01- 2 |
Front and Rear Tie Down Lugs |
|
GME GME L-1A- 2 |
Attachments of the Shock Absorbers Underbody |
|
GME GME L-1A- 3 |
Rear Axle to Body Attachment |
|
GME GME L-1B03- 1 |
Hood Hinges, Wear Test |
|
GME GME L-1B04- 1 |
Laminated Glass - Front Window Panes |
|
GME GME L-1B1201- 1 |
Heating System, Complete |
|
GME GME L-1B1201- 10 |
Linearity Test at Passenger Vehicle Heating and A/C-Systems on Heater Test Bench and in the Climatic Wind Tunnel |
|
GME GME L-1B1201- 11 |
Water Separation |
|
GME GME L-1B1201- 12 |
Performance Measurements on AC-Systems in Passsenger Car |
|
GME GME L-1B1201- 13 |
Dehumidifying Capability of Vehicle Air-Conditioning Units |
|
GME GME L-1B1201- 14 |
Air-Side Characteristics of the Vehicle |
|
GME GME L-1B1201- 2 |
Heater Cores |
|
GME GME L-1B1201- 3 |
Subjective Evaluation of the Heating System During Warm-Up Phase, Tunnel Test |
|
GME GME L-1B1201- 4 |
Pressure, Fatigue and Burst Test of EPDM, Heater and Cooling Water Hoses |
|
GME GME L-1B1201- 5 |
Heating System Maximum Capacity |
|
GME GME L-1B1201- 6 |
Interior Windshield and Side Window Defrosting in a Passenger Car |
|
GME GME L-1B1201- 8 |
Air-Side Characteristics of the A/C and Heater Module |
|
GME GME L-1B1201- 9 |
Windshield Defrosting System Performance Validation for Passenger Vehicles |
|
GME GME L-1B1203- 1 |
Durability Test Sun Visor |
|
GME GME L-1B1205- 2 |
Windshield Wiper Motor Test-Replaced by GME 12516 |
|
GME GME L- 1C/D/E/F/G/H/01-6 |
Buckling Resistance of the Body-English/German; Includes Appendix A-D |
|
GME GME L-1C- 1 |
Roof Crush Resistance |
|
GME GME L-1C1211- 1 |
Durability Test of Assist Handles-Replaced by GME 01118: 02/2004 |
|
GME GME L-1C- 2 |
Roof Water Drainage |
|
GME GME L-1E01- 1 |
Rear Compartment Lid |
|
GME GME L-1E01- 2 |
Fuel Filler Lid |
|
GME GME L-1E01- 3 |
Measurement of Torsional Stiffness of Hoods, Tailgates and Trunk Lids |
|
GME GME L-1E01- 4 |
Trunk Lid-Burglar Alarm/Theft Protection |
|
GME GME L-1E01- 5 |
Trunk Lid Closing Behaviour |
|
GME GME L-1E06- 1 |
Misuse Test of Load Compartment Cover in the Estate |
|
GME GME L-1F/G01- 2 |
Strain Test of the Door Hinge Location, Front and Rear Door-Replaced by GMI L-1F/G01-2 |
|
GME GME L-1F/G01- 4 |
Door - Tensional Test |
|
GME GME L-1F/G01- 5 |
Door Strength Test-Replaced by GMI L-1F/G01-5 |
|
GME GME L-1F/G01- 6 |
Door Stop - Function and Noise |
|
GME GME L-1F/G02- 1 |
Door Closing-Noise Comfort |
|
GME GME L-1F/G03- 1 |
Door Test under Field Conditions |
|
GME GME L-1F/G03- 10 |
Door Lock- Remote Control Wear Test |
|
GME GME L-1F/G03- 11 |
Door Locks (Not Installed), Freeze Test |
|
GME GME L-1F/G03- 19 |
Fatigue Test of Door Look Strikers |
|
GME GME L-1F/G03- 2 |
Pulling of Doors Beyond Stop-Replaced by GMI L-1F/G03-2 |
|
GME GME L-1F/G03- 20 |
Functional and Durability Test of Outside Door Handle, Flap Version |
|
GME GME L-1F/G03- 3 |
Manual Operated Window Lifter |
|
GME GME L-1F/G03- 4 |
Window Regulator, Static Test-Replaced by GMI L-1F/G03-4 |
|
GME GME L-1F/G03- 6 |
Power Window Lifter |
|
GME GME L-1F/G03- 9 |
Lock Cylinder and Inside Door Lock Fatigue Test |
|
GME GME L-1F/G04- 1 |
Window Mounting Rail, Pull Test |
|
GME GME L-1F/G06- 1 |
Door Arm Rest - Static Load |
|
GME GME L-1F/G06- 2 |
Door Arm Rest- Pulsating Load |
|
GME GME L-1F/G- 1 |
Measurement of Frame Stiffness of Front and Rear Doors-Replaced by GMI L-1F/G-1 |
|
GME GME L-1H- 1 |
Slam Test-Tail Gate Caravan |
|
GME GME L-1H- 2 |
Fatigue Test of Tailgate Station Wagon and Hatch Back |
|
GME GME L-1J/K05- 11 |
Seat Springing, Pulsating Load |
|
GME GME L-1J/K06- 1 |
Upholstery Durability Test-Replaced by GMI L-1J/K06-1 |
|
GME GME L-1J/K06- 3 |
Seat Cover, Wear Test |
|
GME GME L-1J/K06- 4 |
Crease Formation on Imitation Leather Seat Covers (Climatic Test)- Replaced by GMI L-1J/K06-4 |
|
GME GME L-1J/K06- 5 |
Trim Seats Wear Tests-Simulation of Getting in and out of the Vehicle |
|
GME GME L-1J/K06- 6 |
Seat Back Trim Wear Test-Replaced by GMI L-1J/K06-6 |
|
GME GME L-1J/K1215- 1 |
Static Seat Belt Anchorages Test-Replaced by GMI L-1J/K1215-1 |
|
GME GME L-1J/K- 2 |
Force Centers |
|
GME GME L-1J/K- 4 |
Requirements to Seats Rear Impact Conditions |
|
GME GME L-1J/K- 9 |
Contour Measurement of Seats and Seat Components-Includes Appendix A |
|
GME GME L-1J03- 2 |
Seat Adjustment-Strength Test |
|
GME GME L-1J03- 3 |
Seat Adjustment, Wear Test |
|
GME GME L-1J03- 5 |
Seatback Adjuster, Durability Test |
|
GME GME L-1J03- 6 |
Power Seats |
|
GME GME L-1J03- 7 |
Lordosis Support Adjustment |
|
GME GME L-1J03- 8 |
Manual Tilt Adjustment - Front Seat |
|
GME GME L-1J05- 10 |
Front Seat Back Lock and Seat Lock |
|
GME GME L-1J05- 11 |
Dynamic Test of Front Seat Back under Side Loads |
|
GME GME L-1J05- 13 |
Test of Threaded Fastening for Seat Belts |
|
GME GME L-1J05- 14 |
Front Backrest Panel with Rigid Pocket - Durability Testing |
|
GME GME L-1J05- 9 |
Front Seatback, Seatback Lock, and Hinge Support Pulsating Load |
|
GME GME L-1J06- 1 |
Wear Test of Sports Seats |
|
GME GME L-1J1201- 1 |
Comfort Evaluation of Heater Mats in Driving Operation |
|
GME GME L-1K03- 1 |
Rear Seat Back Locking, Fatigue Test |
|
GME GME L-1K05- 1 |
Centre Arm Rest-Static Load |
|
GME GME L-1K05- 2 |
Center Arm Rest, Wear Test |
|
GME GME14006 |
Operational Reliability Test for Seat Occupancy Detection Systems with Pressure-Sensitive Resistor Film and Child Seat Detection Systems for Child Seats with Integral Transponder System |
|
GME GME14032 |
Modal Analysis, Test and Evaluation |
|
GME GME14440 |
Stalled Motor Test |
|
GME GME14441 |
Fuse Protection Analysis |
|
GME GME14442 |
Fuse Load Test |
|
GME GME4087 |
Critical Proximity, Maximum Impact Distance between Engine Hood and Trunk Lid / Tailgate |
|
GME GME4134 |
Engine Hood Bowden Cable - Release Force Measurement |
|
GME GME4924 |
Material Settling/Deformation of Vehicle Floor Insulation-Appendix A and B |
|
GME GME4926 |
Durability Test for Lockable Handles-Appendix A and B |
|
GME GME4928 |
Water Absorption of Coverings and Insulation, Corrosion Behaviour of Catches-Appendix A |
|
GME GME6724 |
Durability Test of Passive Seat Height Adjusters |
|
GME GME6731 |
Test of Visibility Through Rear Screen |
|
GME GME6934 |
Squeak & Rattle Evaluation of Seats-Includes Appendix A |
|
GME GME7557 |
Leak Test on Press Nuts |
|
GME GME8226 |
Measurement of Door Closing Energy (Side, Rear and Sliding Doors) |
|
GME GME8270 |
Front Seat Adjuster - Transverse Alternating Load Fatigue Test |
|
GME GME8707 |
Visibility to Traffic Lights-Includes Appendix A |
|
GME GME8708 |
Check Occultation by A-pillar, Panoramic View and View Towards Lower Front Area |
|
GME GME8748 |
Reverberation Time Measurement in the Vehicle |
|
GME GME8749 |
Airborne-Sound Insulation Complete Vehicle |
|
GME GMI L/R-1B1201- 12 |
Performance Measurements on AC-Systems in Passenger Car |
|
GME GMI L/R-1B1201- 5 |
Performance Measurements of Vehicle Heating Systems |
|
GME GMI L/R-1T02- 3 |
Noise Testing of Passenger Compartment Blowers |
|
GME GMI L-0- 11 |
Basic Test |
|
GME GMI L-0- 19 |
Determination of Mass and Trim Heights |
|
GME GMI L-0- 2 |
Determination of the Center of Gravity of a Vehicle |
|
GME GMI L-0- 26 |
Frontal Impact, 30 mph, 0 Degree to 30 Degree - Fixed Rigid Barrier |
|
GME GMI L-0- 27 |
Frontal Impact - Fixed Rigid Barrier (Occupant Protection According to TRIAS, ADR) |
|
GME GMI L-0- 28 |
Side Impact, 50 km/h, 90 Degree - Moving Deformable Barrier (Occupant Protection, Vehicle Structure, Fuel System) |
|
GME GMI L-0- 30 |
Angle Impact, 50 km/h, 30 Degree - Fixed Rigid Barrier with ASD |
|
GME GMI L-0- 31 |
Simulation of Angle Impact, 50 km/h, 30 Degree with ASD - Sled Test |
|
GME GMI L-0- 8 |
Stair-Case-Test to Dixon and Mood |
|
GME GMI L-1- 11 |
Interior Wind Noise Test Procedure-Replaced by GMW8463 |
|
GME GMI L-1- 13 |
Measurement of SRearend Bending Stiffness-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1- 14 |
Measurement of Front Longitudinal Bending Stiffness-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1- 15 |
Steering Column Stiffness-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1- 17 |
Aerodynamic Wind Tunnel Investigations on Full Scale Vehicles and Vehicle Models (1:1 and 1:5)-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-13D- 1 |
Coolant Flow Through the Heater and the Resistance of the Heater Core in the Vehicle (Formerly GME L-13D-1)-English Translation Available, ITDC Release, Draft for Harmonization |
|
GME GMI L-1- 4 |
Occupant Protection in Interior Impacts Investigation of the Energy Absorption of Parts in the Passenger Compartment |
|
GME GMI L-1- 5 |
Fundamental Body Vibration Complete Vehicle-English Translation Available |
|
GME GMI L-1- 6 |
Fundamental Body Vibrations Body in White |
|
GME GMI L-1- 8 |
Measurement of Torsional Stiffness-English Translation Available: ITDC Release, Draft for Harmonization |
|
GME GMI L-1- 9 |
Measurement of Bending Stiffness of Body in White-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1A01- 3 |
Static Test of the Tie-Down Eyelets (Cargo Shift Protection)-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1A01- 4 |
Measurement of Floor Panel Stiffness-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1A02R- 1 |
Side Air Bag Misuse Test Procedure for Side Impact Detection Systems Based on Door Internal Pressure Sensing-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1B04- 2 |
Assessment of Reflections of the Instrument Panel in the Windshield by Means of Photometric Measurement-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1B1201- 14 |
Air-Side Characteristics of the Vehicle (formerly GME L-1B1201-14)- English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1B1201- 6 |
Drying of Windscreen and Front Side Windows (formerly GME L-1B1201- 6)-English Translation Available |
|
GME GMI L-1B1201- 8 |
Air-Side Characteristics of the A/C and Heater Module (formerly GME L- 1B1201-8)-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1B- 2 |
Measurement of Stiffness of Shock Absorbing Strut Tower-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L- 1C/D/E/F/G/H01-6 |
Buckling Resistance of Body-English/German; Inactive and Replaced by: GME L-1C/D/E/F/G/H01-6 |
|
GME GMI L-1C- 1 |
Roof Crush Resistance Test (formerly GME L-1C-1)-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1E01- 3 |
Measurement of Torsional Stiffness of Hoods, Tailgates and Trunk Lids (formerly GME L-1E01-3)-English Translation Available;ITDC Release,Draft for Harmonization |
|
GME GMI L-1F/G01- 2 |
Door Lowering Measurement for Front and Rear Doors |
|
GME GMI L-1F/G01- 5 |
Door Strength Test (Formerly GME L-1F/G01-5) |
|
GME GMI L-1F/G03- 1 |
Door Test under Field Conditions-Replaced by GME L-1F/G03-1 |
|
GME GMI L-1F/G03- 2 |
Pillar Stiffness Measurement with Excessive Pulling Force Applied to Door |
|
GME GMI L-1F/G03- 4 |
Window Regulator - Static Test (Formerly GME L-1F/G03-4) |
|
GME GMI L-1F/G- 1 |
Measurement of Frame Stiffness of Front and Rear Doors-Replaces GME L/R-1F/G-1 |
|
GME GMI L-1F/G- 2 |
Measurement of Lateral Belt Line Stiffness of Front and Rear Doors |
|
GME GMI L-1F/G- 3 |
Pillar Stiffness Measurement with Door Lowering Stress |
|
GME GMI L-1H- 3 |
Measurement of Bending Stiffness of Hoods and Tailgates-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1H- 4 |
Measurement of Lateral Stiffness of Hinges of Hood, Trunk Lid and Tailgate-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1J/K06- 1 |
Upholstery Durability Test (Formerly GME L-1J/K06-1) |
|
GME GMI L-1J/K06- 4 |
Crease Formation on Imitation Leather Seat Covers (Climatic Test) (Formerly GME L-1J/K06-4) |
|
GME GMI L-1J/K06- 6 |
Seat Back Trim, Wear Test (Formerly GME L-1J/K06-6) |
|
GME GMI L-1J/K1215- 1 |
Static Seat Belt Anchorages Test (Formerly GME L-1J/K1215-1) |
|
GME GMI L-1J/K1216- 1 |
Seat and Head Restraint Pendulum Test, Investigation of the Energy Absorption Capacity of Seats and Head Restraints |
|
GME GMI L-1J/K- 5 |
Static Seat Anchorages Test |
|
GME GMI L-1J/K- 6 |
Dynamic Seat Anchorages Test (Sled Test) |
|
GME GMI L-1J/K- 7 |
Seat Back Torque Test (Single Seat) |
|
GME GMI L-1J/K- 8 |
Seat Back Torque Test (Seat Bench) |
|
GME GMI L-1J03- 7 |
Adjuster Lordosis Support, Durability Test-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME GMI L-1J06- 1 |
Wear Test of Sport Seats-English Translation Available;ITDC Release, Draft for Harmonization |
|
GME OPEL 351 |
Testing of Staining Behavior of Moulded Headlinings through Dry Dirt- English/German |
|
GME QK 000131 |
Polyamide 66 with 30 % Glass Fibres-Replaced by QK 003013 H |
|
GME QK 000264 |
ABS-Moulding Compounds-Replaced by QK 002014 |