|
GMNA A |
Data Organization |
|
GMNA A- 127 |
Drawing Notes |
|
GMNA A- 129 |
Drawing Titles |
|
GMNA A- 133 |
Drawing Revisions |
|
GMNA A- 137 |
Drawing Quality Assurance |
|
GMNA A- 138 |
Labels and Identification |
|
GMNA A- 139 |
Drawing Mediums and Reproductions |
|
GMNA A- 143 |
Layout Practice |
|
GMNA A- 145 |
Rigid Bent Tubes and Tube Bending |
|
GMNA A- 161 |
Body Drafting Practice |
|
GMNA A- 165 |
Pictorial Drawings |
|
GMNA A- 21 |
Drawing Types |
|
GMNA A- 31 |
Drawing and Layout Forms |
|
GMNA A4 |
Electronic Math Model and Drawing Data Creation Standard Data Organization - Unigraphics-Replaced by A7A |
|
GMNA A- 51 |
Line Conventions |
|
GMNA A- 53 |
Sectioning |
|
GMNA A- 57 |
Lettering |
|
GMNA A- 59 |
Abbreviations and Symbols |
|
GMNA A5A |
Electronic Math Model and Drawing Data Creation Standard Data Organization - Unigraphics |
|
GMNA A5B |
Electronic Math Model and Drawing Data Creation Standard Data Organization - Unigraphics |
|
GMNA A- 61 |
Projection and Descriptive Geometry |
|
GMNA A- 62 |
Pipe Threads |
|
GMNA A- 9 |
Metric Dimensioning System |
|
GMNA B- 1 |
Springs |
|
GMNA B- 16 |
Gears |
|
GMNA B- 18 |
Involute Splines |
|
GMNA B- 47 |
Bearings |
|
GMNA B- 61.01 |
Screw Threads |
|
GMNA D- 1 |
Electrical Wiring Drafting Practice |
|
GMNA DESIGN VOL 2 001 |
Electronic Math Model and Drawing Data Creation Standard What the "Standard" is Not |
|
GMNA DESIGN VOL 2 A |
Data Organization |
|
GMNA DESIGN VOL 2 A1 |
Electronic Math Model and Drawing Data Creation Standard Data Organization - CADAM (Mainframe) |
|
GMNA DESIGN VOL 2 A10A |
Electronic Math Model and Drawing Data Creation Standard Data Organization - Unigraphics-Replaced by Design Vol 2 A11A |
|
GMNA DESIGN VOL 2 A10B |
Data Creation Standards - Unigraphics-Replaced by GM Design Vol 2 A11B |
|
GMNA DESIGN VOL 2 A11A |
ELECTRONIC MATH MODEL AND DRAWING DATA CREATION STANDARD DATA ORGANIZATION UNIGRAPHICS |
|
GMNA DESIGN VOL 2 A11B |
ELECTRONIC MATH MODEL AND DRAWING DATA CREATION STANDARD DATA ORGANIZATION UNIGRAPHICS NX WITH TEAMCENTER |
|
GMNA DESIGN VOL 2 A2 |
Electronic Math Model and Drawing Data Creation Standard Data Organization - CGS |
|
GMNA DESIGN VOL 2 A6 |
Electronic Math Model and Drawing Data Creation Standard Data Organization - UGMX (Workstation) |
|
GMNA DESIGN VOL 2 A7A |
Electronic Math Model and Drawing Data Creation Standard Data Organization - Unigraphics-Replaced By GM Design Vol 2 A8A |
|
GMNA DESIGN VOL 2 A8B |
Electronic Math Model and Drawing Data Creation Standard Data Organization - Unigraphics with GM/PDM |
|
GMNA DESIGN VOL 2 A91 |
Dimensioning and Tolerancing Addendum - 1997-Replaced by DESIGN VOL 2 C2 |
|
GMNA DESIGN VOL 2 B |
Electronic Math Model and Drawing Data Creation Standard Geometry |
|
GMNA DESIGN VOL 2 B2 |
Electronic Math Model and Drawing Data Creation Standard Geometry - CGS |
|
GMNA DESIGN VOL 2 C |
Electronic Math Model and Drawing Data Creation Standard Drawing Data - Introduction-Replaced by DESIGN VOL 2 C1 |
|
GMNA DESIGN VOL 2 C1 |
Electronic Math Model and Drawing Data Creation Standard Drawing Data Organization - Format Requirements |
|
GMNA DESIGN VOL 2 C2 |
Dimensioning and Tolerancing Addendum - 1997 |
|
GMNA DESIGN VOL 2 C2A |
Global Dimensioning and Tolerancing Addendum - 2001 |
|
GMNA DESIGN VOL 2 C2B |
Global Dimensioning And Tolerancing Addendum 2004 |
|
GMNA DESIGN VOL 2 C3 |
Electronic Math Model and Drawing Data Creation Standard Drawing Data Organization - Drawing Views and Sections |
|
GMNA DESIGN VOL 2 C5 |
Electronic Math Model and Drawing Data Creation Standard Drawing Data - Unigraphics V11.X |
|
GMNA DESIGN VOL 2 C6 |
Electronic Math Model and Drawing Data Creation Standard Drawing Data - UGMX (Workstation) |
|
GMNA DESIGN VOL 2 D |
Electronic Math Model and Drawing Data Creation Standard User Defined Attributes |
|
GMNA DESIGN VOL 2 E |
Section Index |
|
GMNA DESIGN VOL 2 E0A |
Electronic Math Model and Drawing Data Creation Standard TDMF |
|
GMNA DESIGN VOL 2 E0B |
Electrical Math and Drawing Data Creation Standard GM Product Manager |
|
GMNA DESIGN VOL 2 E7C |
Management of Unigraphics V13 Data with GM/PDM 4.0 |
|
GMNA DESIGN VOL 2 F |
Electronic Math Model and Drawing Data Creation Standard Glossary |
|
GMNA DESIGN VOL 2 G |
Electronic Math Model and Drawing Data Creation Standard Reference Sources |
|
GMNA DESIGN VOL 2 H |
Electronic Math Model and Drawing Data Creation Standard Math Data Sharing Agreement |
|
GMNA DESIGN VOL 2 INTRO |
Electronic Math Model and Drawing Data Creation Standard |
|
GMNA DESIGN VOL 2 PREFACE |
Electronic Math Model and Drawing Data Creation Standard |
|
GMNA DESIGN VOL 2 TOC |
Electronic Math Model and Drawing Creation Standard |
|
GMNA E- 101 |
Metallic Coatings |
|
GMNA E- 111 |
Welding |
|
GMNA E- 129 |
Brazing |
|
GMNA E- 13 |
Castings |
|
GMNA E- 133 |
Soft Soldering |
|
GMNA E- 2 |
Stampings |
|
GMNA E- 25 |
Die Castings |
|
GMNA E- 33 |
Forgings |
|
GMNA E- 45 |
Powder Metallurgy |
|
GMNA E- 53 |
Plastics |
|
GMNA E- 73 |
Rubber |
|
GMNA E- 91 |
Surface Texture Symbols |
|
GMNA GM E502 |
Type B Spring Nuts General Specifications |
|
GMNA GM E510 |
"J" Shape and "U" Shape Spring Nut Assembly Data |
|
GMNA GM INCH VOL 1 INDEX |
Numerical Index |
|
GMNA GMN10068 |
Global Supplier Serviceability Requirements |
|
GMNA GMN10070 |
PPO Subassembly Quote and Process Information |
|
GMNA GMN11049 |
Paint and Polymer Engineering Mold Standards |
|
GMNA GMN11155 |
Specification for Steering Intermediate Shaft and Boot/Seal Component-Replaced by GMW14088 |
|
GMNA GMN11220 |
Design Review Based on Failure Modes |
|
GMNA INTRO.001 |
Electronic Math Model and Drawing Data Creation Standard |
|
GMNA PREFACE.001 |
Electronic Math Model and Drawing Data Creation Standard |
|
GMNA STANDARD.001 |
Electronic Math Model and Drawing Data Creation Standard; What the "Standard" is Not |
|
GMNA STD_DIR |
Standards Information Directory |
|
GMNA VOL I SEC B |
Section B - Hexagon Bolts |
|
GMNA VOL I SEC B |
Section B - Gages and Gaging |
|
GMNA VOL I SEC B |
Section B - Plated and Coated Finishes for Externally Threaded Fasteners |
|
GMNA VOL I SEC B |
Section B - Table of Contents/Numerical Index |
|
GMNA VOL I SEC B |
Section B - Studs |
|
GMNA VOL I SEC C |
Section C - Machine Screws |
|
GMNA VOL I SEC C |
Section C - Table of Contents/Numerical Index |
|
GMNA VOL I SEC C |
Section C - Gages and Gaging |
|
GMNA VOL I SEC C |
Section C - Lock Washer Assemblies |
|
GMNA VOL I SEC C |
Section C - Cap Screws |
|
GMNA VOL I SEC C |
Section C - Set Screws |
|
GMNA VOL I SEC D |
Section D - Round Head Metallic Drive Screws |
|
GMNA VOL I SEC D |
Section D - Sealing Compound Coating for Screws |
|
GMNA VOL I SEC D |
Section D - Tapping Screws |
|
GMNA VOL I SEC D |
Section D - Recommended Hole Sizes for Tapping Screws |
|
GMNA VOL I SEC D |
Section D - Table of Contents/Numerical Index |
|
GMNA VOL I SEC D |
Section D - Mechanical and Quality Requirements for Tapping Screws |
|
GMNA VOL I SEC E |
Section E - Weld Nuts |
|
GMNA VOL I SEC E |
Section E - Self Piercing or Clinch Nuts |
|
GMNA VOL I SEC E |
Section E - Hexagon Lock Nuts |
|
GMNA VOL I SEC E |
Section E - Metallurgical Requirements for Steel Nuts |
|
GMNA VOL I SEC E |
Section E - Stamped Nuts |
|
GMNA VOL I SEC E |
Section E - Table of Contents/Numerical Index |
|
GMNA VOL I SEC E |
Section E - Wing Nuts |
|
GMNA VOL I SEC E |
Section E - Hexagon Nuts |
|
GMNA VOL I SEC E |
Section E - Spring Nuts |
|
GMNA VOL I SEC E |
Section E - Helical Thread Inserts |
|
GMNA VOL I SEC E |
Section E - Tee Nuts |
|
GMNA VOL I SEC E |
Section E - Square Nuts |
|
GMNA VOL I SEC E |
Section E - Tapping Inserts |
|
GMNA VOL I SEC E |
Section E - Crown Nuts |
|
GMNA VOL I SEC E |
Section E - Gages and Gaging for Slots in Slotted Nuts |
|
GMNA VOL I SEC F |
Section F - Flat Washers |
|
GMNA VOL I SEC F |
Section F - Lock Washers |
|
GMNA VOL I SEC F |
Section F - Finish Washers |
|
GMNA VOL I SEC F |
Section F - Table of Contents/Numerical Index |
|
GMNA VOL I SEC G |
Section G - Solid Rivets |
|
GMNA VOL I SEC G |
Section G - Table of Contents/Numerical Index |
|
GMNA VOL I SEC G |
Section G - Eyelets |
|
GMNA VOL I SEC G |
Section G - Aluminum Rivets |
|
GMNA VOL I SEC G |
Section G - Tubular Rivets |
|
GMNA VOL II SEC H |
Section H - Table of Contents/Numerical Index |
|
GMNA VOL II SEC H |
Section H - Nails and Tacks |
|
GMNA VOL II SEC H |
Section H - Staples |
|
GMNA VOL II SEC H |
Section H - Nails |
|
GMNA VOL II SEC J |
Section J - Table of Contents/Numerical Index |
|
GMNA VOL II SEC J |
Section J - Plugs |
|
GMNA VOL II SEC J |
Section J - Pins |
|
GMNA VOL II SEC J |
Section J - Button Plugs |
|
GMNA VOL II SEC J |
Section J - Retainer Springs |
|
GMNA VOL II SEC J |
Section J - Woodruff Keys |
|
GMNA VOL II SEC K |
Section K - Table of Contents/Numerical Index |
|
GMNA VOL II SEC K |
Section K - Hose Clamps |
|
GMNA VOL II SEC K |
Section K - Clips |
|
GMNA VOL II SEC L |
Section L - Cocks |
|
GMNA VOL II SEC L |
Section L - Tube Fittings |
|
GMNA VOL II SEC L |
Section L - Table of Contents/Numerical Index |
|
GMNA VOL II SEC L |
Section L - Lubrication Fittings |
|
GMNA VOL II SEC L |
Section L - Cups |
|
GMNA VOL II SEC M |
Section M - Table of Contents/Numerical Index |
|
GMNA VOL II SEC M |
Section M - Pipe Fittings |
|
GMNA VOL II SEC M |
Section M - Automotive Pipe Fittings |
|
GMNA VOL II SEC N |
Section N - Table of Contents/Numerical Index |
|
GMNA VOL II SEC N |
Section N - Bearing Lock Nuts and Washers |
|
GMNA VOL II SEC N |
Section N - Ball Bearings |
|
GMNA VOL II SEC R |
Section R - Electrical Fuses |
|
GMNA VOL II SEC R |
Section R - Table of Contents/Numerical Index |
|
GMNA VOL II SEC R |
Section R - Battery Terminals |
|
GMNA VOL II SEC R |
Section R - Insulating Nipples |
|
GMNA VOL II SEC R |
Section R - Electrical Terminals |
|
GMNA VOL II SEC R |
Section R - Lamps and Lamp Units |
|
GMNA VOL II SEC T |
Section T - Ball Joints |
|
GMNA VOL II SEC T |
Section T - Tire Valve Fittings |
|
GMNA VOL II SEC T |
Section T - V-Belts |
|
GMNA VOL II SEC T |
Section T - Table of Contents/Numerical Index |
|
GMNA VOL II SEC T |
Section T - Annular Gaskets |
|
GMNA VOL II SEC T |
Section T - Rod End Clevises and Eyes |
|
GMNA VOL II SEC T |
Section T - Tire Valve Assemblies |
|
GMNA VOL II SEC T |
Section T - Hoses and Tubing |
|
GMNA VOL II SEC T |
Section T - Tapping Screws |
|
GMNA VOL II SEC T |
Section T - Rubber Grommets |
|
GMNA VOL II SEC V |
Section V - Tube Nuts |
|
GMNA VOL II SEC V |
Section V - Hexagon Bolts |
|
GMNA VOL II SEC V |
Section V - Self-Piercing Nuts |
|
GMNA VOL II SEC V |
Section V - Flat Washers |
|
GMNA VOL II SEC V |
Section V - Ground Rules for Specification of Automotive Fasteners |
|
GMNA VOL II SEC V |
Section V - Machine Screws |
|
GMNA VOL II SEC V |
Section V - Projection Weld Screws |
|
GMNA VOL II SEC V |
Section V - Tie Straps |
|
GMNA VOL II SEC V |
Section V - Stamped Nuts |
|
GMNA VOL II SEC V |
Section V - Tubular Rivets |
|
GMNA VOL II SEC V |
Section V - Spring Nuts |
|
GMNA VOL II SEC V |
Section V - Design Guide for Determining the Length of Thread Engagement for Various Metals Recommended Metric Hole Sizes |
|
GMNA VOL II SEC V |
Section V - Power Sockets |
|
GMNA VOL II SEC V |
Section V - Hex Nuts |
|
GMNA VOL II SEC V |
Section V - Tapping Screws |
|
GMNA VOL II SEC V |
Section V - Lock Washers |